填充机
我们在机器FM24标准型填充机的基础上,引入PLC和人机介面(触摸屏)控制,增加了直线导向导轨和旋转式夹紧机构,设计而成这种标准型填充设备,这类机器有24工装和48工装两种,填充长度可达到6M,**填充直径为Φ12.7mm。由于引入PLC和编码计数装置。
我们可以在机器上十分方便地调整所需的长度,只要在触摸屏输入要填充的实际长度(空管长度)机器便自动调整位置,这一点较人工电动调整更为快捷、准确、而且在填充过程中的位置关系保证十分准确。机器的导向管内装有螺旋喷嘴,芯棒(挂钩)的外露是可以通过电动调整较前一种机器人工调整方便得多。 我们设计出气动夹具,较短的元件(1500mm一下),可以快速地将24支元件一次装夹,大大提高了生产效率。
近年,我们改良的喷粉嘴的机构,采用三层导管机构代替传统的螺旋喷粉嘴,镁粉的流量加大,填充效率得到提高。FM24-PLC无论采用螺旋喷嘴或三导管结构,都是目前国内外先进的填充设备。 |
地 区:广东 肇庆 等 级: 参考价格: 认 证: 规 格:商谈 供货数量:100 供货能力:100 发布日期:2014-05-26 10:16:25 有 效 期:长期有效 发布用户:tubemachines 发 布 IP:183.50.130.0
电 话:0758-2771912 传 真:0758-2743414
地 址: | 中国广东省肇庆市端州区大冲水基村(省719地质队旁) | 联 系:麦小姐 电子邮箱:may@zqfeihong.com 其它产品:点击查看该会员其它产品 在线留言:
|
[参考图片]
|
|
友情提示:
信息由用户自行发布,采用请谨慎,我们鼓励您当面交易。如有不符合法规或造成侵权,请及时通知本站更正或删除,具体联系方式见页面底部联系我们。名站在线只为传递信息,我们不做任何双方证明,也不承担任何法律责任。 信息转载,请标明来源于www.fwol.cn ,谢谢。 |
当前页在本站[名站在线]7天内点击次数(点击次数为零的日期不显示): |
信息评估: |
(还没有网友对该信息作出评估,你想为该信息提供第一个评估吗?) |
PA6 73G30HSL BK416美国杜邦Zytel 30%玻纤增强热稳定尼龙6塑料PA6 73G30HSL BK416美国杜邦Zytel 30%玻纤增强热稳定尼龙6塑料18024445500
General information Value Unit Test Standard
Resin Identification PA6-GF30 - -
Part Marking Code >PA6-GF30< - ISO 11469
Rheological properties dry / cond Unit Test Standard
Viscosity number 150 / cm&sup3;/g ISO 307, 1157, 1628
Moulding shrinkage, parallel 0.2 / % ISO 294-4, 2577
Moulding shrinkage...PA6 73G30HSL NC010美国杜邦Zytel热稳定30%玻纤增强注塑级聚酰胺PA6 73G30HSL NC010美国杜邦Zytel热稳定30%玻纤增强注塑级聚酰胺6塑料18024445500
General information Value Unit Test Standard
Resin Identification PA6-GF30 - -
Part Marking Code >PA6-GF30< - ISO 11469
Rheological properties dry / cond Unit Test Standard
Viscosity number 150 / cm&sup3;/g ISO 307, 1157, 1628
Moulding shrinkage, parallel 0.2 / % ISO 294-4, 2577
Moulding sh...PA6 73G30L NC010美国杜邦Zytel 30%玻纤增强注塑成型聚酰胺6广东PA6 73G30L NC010美国杜邦Zytel 30%玻纤增强注塑成型聚酰胺618024445500
General information Value Unit Test Standard
Resin Identification PA6-GF30 - -
Part Marking Code >PA6-GF30< - ISO 11469
Rheological properties dry / cond Unit Test Standard
Viscosity number 150 / cm&sup3;/g ISO 307, 1157, 1628
Moulding shrinkage, parallel 0.2 / % ISO 294-4, 2577
Moulding shrinkage, ...PA6 73G30T BK261美国杜邦Zytel 30%玻纤增强增韧尼龙6树脂注塑成PA6 73G30T BK261美国杜邦Zytel 30%玻纤增强增韧尼龙6树脂注塑成型18024445500
General information Value Unit Test Standard
Resin Identification PA6-IGF30 - -
Part Marking Code >PA6-IGF30< - ISO 11469
Mechanical properties dry / cond Unit Test Standard
Tensile Modulus 9400 / 5600 MPa ISO 527-1/-2
Stress at break 170 / 110 MPa ISO 527-1/-2
Strain at break 3 / 6 % ISO 527-1/-2
Flex...PA6 73G30T NC010美国杜邦Zytel 30%玻纤增强增韧尼龙6树脂注塑成PA6 73G30T NC010美国杜邦Zytel 30%玻纤增强增韧尼龙6树脂注塑成型18024445500
General information Value Unit Test Standard
Resin Identification PA6-IGF30 - -
Part Marking Code >PA6-IGF30< - ISO 11469
Rheological properties dry / cond Unit Test Standard
Viscosity number 135 / cm&sup3;/g ISO 307, 1157, 1628
Moulding shrinkage, parallel 0.2 / % ISO 294-4, 2577
Moulding shr...
|
|
|
|
|