PA66 AKV 30 G HR DUS023 900116µÂ¹úÀÊÊ¢Durethan 30%²£ÏËÔöÇ¿ÄáÁú66ËÜÁÏ£¨18024445500£©

PA 66, 30 % glass fibers, injection molding, improved flowability, hydrolysis stabilized, improved surface finish, GIT/WIT



ISO Shortname: ISO1874-PA 66, GHRW, 14-080, GF30

Property Test Condition Unit Standard guide value
d.a.m. cond.
Rheological properties
C Molding shrinkage, parallel 60x60x2; 290 ¡ãC / MT 80 ¡ãC; 600 bar % ISO 294-4 0.64¡¡
C Molding shrinkage, transverse 60x60x2; 290 ¡ãC / MT 80 ¡ãC; 600 bar % ISO 294-4 0.82¡¡
Post- shrinkage, parallel 60x60x2; 120 ¡ãC; 4 h % ISO 294-4 0.05¡¡
Post- shrinkage, transverse 60x60x2; 120 ¡ãC; 4 h % ISO 294-4 0.04¡¡

Mechanical properties (23 ¡ãC/50 % r. h.)
C Tensile modulus 1 mm/min MPa ISO 527-1,-2 8500 5600
C Tensile Stress at break 5 mm/min MPa ISO 527-1,-2 135 90
C Tensile Strain at break 5 mm/min % ISO 527-1,-2 3.2 6.5
C Charpy impact strength 23 ¡ãC kJ/m² ISO 179-1eU 70 65
C Charpy impact strength -30 ¡ãC kJ/m² ISO 179-1eU 55¡¡
C Charpy notched impact strength 23 ¡ãC kJ/m² ISO 179-1eA <10 <10
C Charpy notched impact strength -30 ¡ãC kJ/m² ISO 179-1eA <10 <10
Izod impact strength 23 ¡ãC kJ/m² ISO 180-1U 60 60
Izod impact strength -30 ¡ãC kJ/m² ISO 180-1U 45¡¡
Izod notched impact strength 23 ¡ãC kJ/m² ISO 180-1A <10 <10
Izod notched impact strength -30 ¡ãC kJ/m² ISO 180-1A <10 <10
Flexural modulus 2 mm/min MPa ISO 178-A 8000 5600
Flexural strength 2 mm/min MPa ISO 178-A 215 150
Flexural strain at flexural strength 2 mm/min % ISO 178-A 3.8 5.8
Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178-A 210 130
C Puncture maximum force 23 ¡ãC N ISO 6603-2 800¡¡
C Puncture maximum force -30 ¡ãC N ISO 6603-2 650¡¡
C Puncture energy 23 ¡ãC J ISO 6603-2 2.5¡¡
C Puncture energy -30 ¡ãC J ISO 6603-2 2.0¡¡

Thermal properties
C Melting temperature 10 ¡ãC/min ¡ãC ISO 11357-1,-3 259¡¡
C Temperature of deflection under load 1.80 MPa ¡ãC ISO 75-1,-2 200¡¡
C Temperature of deflection under load 0.45 MPa ¡ãC ISO 75-1,-2 245¡¡
C Temperature of deflection under load 8.00 MPa ¡ãC ISO 75-1,-2 75¡¡
C Coefficient of linear thermal expansion, parallel 23 to 55 ¡ãC 10-4/K ISO 11359-1,-2 0.3¡¡
C Coefficient of linear thermal expansion, transverse 23 to 55 ¡ãC 10-4/K ISO 11359-1,-2 0.9¡¡

Other properties (23 ¡ãC)
C Density¡¡kg/m³ ISO 1183 1343¡¡

Processing conditions for test specimens
C Injection molding-Melt temperature¡¡¡ãC ISO 294 290¡¡
C Injection molding-Mold temperature¡¡¡ãC ISO 294 80¡¡

Processing recommendations
Drying temperature dry air dryer¡¡¡ãC - 80¡¡
Drying time dry air dryer¡¡h - 2-6¡¡
Residual moisture content¡¡% Acc. to Karl Fischer¡¡0.03-0.12¡¡
Melt temperature (Tmin - Tmax)¡¡¡ãC - 280-300¡¡
Mold temperature¡¡¡ãC - 80-120¡¡

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.