PA66 AKV 30 GIT H2.0 900116µÂ¹úÀÊÊ¢Durethan 30%²£ÏËÈÈÀÏ»¯Îȶ¨ÄáÁú66ËÜÁÏ£¨18024445500£©

PA 66, 30 % glass fibers, injection molding, heat-aging stabilized, improved surface finish, GIT/WIT



ISO Shortname: ISO 1874-PA 66, GHR, 14-090, GF30

Property Test Condition Unit Standard guide value
d.a.m. cond.
Rheological properties
Molding shrinkage, parallel 150x105x3; 290 ¡ãC / MT 80 ¡ãC; 500 bar % acc. ISO 2577 0.22¡¡
Molding shrinkage, transverse 150x105x3; 290 ¡ãC / MT 80 ¡ãC; 500 bar % acc. ISO 2577 0.93¡¡
Post- shrinkage, parallel 150x105x3; 120 ¡ãC; 4 h % acc. ISO 2577 0.04¡¡
Post- shrinkage, transverse 150x105x3; 120 ¡ãC; 4 h % acc. ISO 2577 0.08¡¡

Mechanical properties (23 ¡ãC/50 % r. h.)
C Tensile modulus 1 mm/min MPa ISO 527-1,-2 9200 6600
C Tensile Stress at break 5 mm/min MPa ISO 527-1,-2 190 120
C Tensile Strain at break 5 mm/min % ISO 527-1,-2 4.0 6.0
C Charpy impact strength 23 ¡ãC kJ/m² ISO 179-1eU 70 80
C Charpy impact strength -30 ¡ãC kJ/m² ISO 179-1eU 60 60
C Charpy notched impact strength 23 ¡ãC kJ/m² ISO 179-1eA 10 15
C Charpy notched impact strength -30 ¡ãC kJ/m² ISO 179-1eA < 10 < 10
Charpy notched impact strength -40 ¡ãC kJ/m² ISO 179-1eA < 10 < 10
Izod impact strength 23 ¡ãC kJ/m² ISO 180-1U 60 70
Izod impact strength -30 ¡ãC kJ/m² ISO 180-1U 50 50
Izod notched impact strength 23 ¡ãC kJ/m² ISO 180-1A 10 15
Izod notched impact strength -30 ¡ãC kJ/m² ISO 180-1A 10 10
Flexural modulus 2 mm/min MPa ISO 178-A 8500 6000
Flexural strength 2 mm/min MPa ISO 178-A 280 180
Flexural strain at flexural strength 2 mm/min % ISO 178-A 4.5 6.0
Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178-A 260 160
C Puncture maximum force 23 ¡ãC N ISO 6603-2 850 1040
C Puncture maximum force -30 ¡ãC N ISO 6603-2 770¡¡
C Puncture energy 23 ¡ãC J ISO 6603-2 2.5 4.0
C Puncture energy -30 ¡ãC J ISO 6603-2 2.3¡¡
Ball indentation hardness¡¡N/mm² ISO 2039-1 215¡¡

Thermal properties
C Melting temperature 10 ¡ãC/min ¡ãC ISO 11357-1,-3 260¡¡
C Temperature of deflection under load 1.80 MPa ¡ãC ISO 75-1,-2 230¡¡
C Temperature of deflection under load 0.45 MPa ¡ãC ISO 75-1,-2 250¡¡
C Temperature of deflection under load 8.00 MPa ¡ãC ISO 75-1,-2 90¡¡
Vicat softening temperature 50 N; 120 ¡ãC/h ¡ãC ISO 306 >230¡¡
C Coefficient of linear thermal expansion, parallel 23 to 55 ¡ãC 10-4/K ISO 11359-1,-2 0.3¡¡
C Coefficient of linear thermal expansion, transverse 23 to 55 ¡ãC 10-4/K ISO 11359-1,-2 0.8¡¡
C Burning behavior UL 94 (1.6 mm)¡¡Class UL 94 HB¡¡
Burning behavior UL 94¡¡Class UL 94 HB¡¡
C Oxygen index Method A % ISO 4589-2 25¡¡
Glow wire test (GWFI) 2.0 mm ¡ãC IEC 60695-2-12 650¡¡
Burning behavior US-FMVSS302 >=1.0 mm¡¡ISO 3795 passed¡¡
C Vicat softening temperature 50 N; 50 ¡ãC/h ¡ãC ISO 306 > 230¡¡

Electrical properties (23 ¡ãC/50 % r. h.)
C Relative permittivity 100 Hz - IEC 60250 4.0 8.0
C Relative permittivity 1 MHz - IEC 60250 3.8 4.2
C Dissipation factor 100 Hz 10-4 IEC 60250 80 2100
C Dissipation factor 1 MHz 10-4 IEC 60250 160 700
C Volume resistivity¡¡Ohm¡¤m IEC 60093 1E13 1E10
C Surface resistivity¡¡Ohm IEC 60093 1E15 1E13
C Electric strength 1 mm kV/mm IEC 60243-1 45 40
C Comparative tracking index CTI Solution A V IEC 60112 475¡¡

Other properties (23 ¡ãC)
C Water absorption (Saturation value) Water at 23 ¡ãC % ISO 62 6.0¡¡
C Water absorption (Equilibrium value) 23 ¡ãC; 50 % RH % ISO 62 2.0¡¡
C Density¡¡kg/m³ ISO 1183 1368¡¡
Bulk density¡¡kg/m³ ISO 60 700¡¡

Processing conditions for test specimens
C Injection molding-Melt temperature¡¡¡ãC ISO 294 290¡¡
C Injection molding-Mold temperature¡¡¡ãC ISO 294 80¡¡

Processing recommendations
Drying temperature dry air dryer¡¡¡ãC - 80¡¡
Drying time dry air dryer¡¡h - 2-6¡¡
Residual moisture content¡¡% Acc. to Karl Fischer¡¡0.03-0.12¡¡
Melt temperature (Tmin - Tmax)¡¡¡ãC - 280-300¡¡
Mold temperature¡¡¡ãC - 80-120¡¡

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.