PA66 AKV 30 H3.0 000000µÂ¹úÀÊÊ¢Durethan 30%²£ÏËÈÈÀÏ»¯Îȶ¨×¢ËÜÄáÁú66ËÜÁÏ£¨18024445500£©

PA 66, 30 % glass fibers, injection molding, heat-aging stabilized

ISO/ ASTM

ISO Shortname: ISO 1874-PA 66, GHR, 14-090, GF30

Property Test Condition Unit Standard guide value
d.a.m. cond.
Rheological properties
C Molding shrinkage, parallel 60x60x2; 300 ¡ãC / MT 80 ¡ãC; 600 bar % ISO 294-4 0.4¡¡
C Molding shrinkage, transverse 60x60x2; 300 ¡ãC / MT 80 ¡ãC; 600 bar % ISO 294-4 1.1¡¡
Post- shrinkage, parallel 60x60x2; 120 ¡ãC; 4 h % ISO 294-4 0.04¡¡
Post- shrinkage, transverse 60x60x2; 120 ¡ãC; 4 h % ISO 294-4 0.1¡¡

Mechanical properties (23 ¡ãC/50 % r. h.)
C Tensile modulus 1 mm/min MPa ISO 527-1,-2 9500 6000
C Tensile Stress at break 5 mm/min MPa ISO 527-1,-2 185 115
C Tensile Strain at break 5 mm/min % ISO 527-1,-2 3.5 6.5
C Charpy impact strength 23 ¡ãC kJ/m² ISO 179-1eU 75 90
C Charpy impact strength -30 ¡ãC kJ/m² ISO 179-1eU 60 60
C Charpy notched impact strength 23 ¡ãC kJ/m² ISO 179-1eA 10 15
C Charpy notched impact strength -30 ¡ãC kJ/m² ISO 179-1eA 10 10
Izod impact strength 23 ¡ãC kJ/m² ISO 180-1U 65 70
Izod impact strength -30 ¡ãC kJ/m² ISO 180-1U 55 55
Izod notched impact strength 23 ¡ãC kJ/m² ISO 180-1A 10 15
Izod notched impact strength -30 ¡ãC kJ/m² ISO 180-1A < 10 < 10
Flexural modulus 2 mm/min MPa ISO 178-A 9200 5500
Flexural strength 2 mm/min MPa ISO 178-A 280 185
Flexural strain at flexural strength 2 mm/min % ISO 178-A 4.2 6.0
Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178-A 260 145
C Puncture maximum force 23 ¡ãC N ISO 6603-2 1000 1100
C Puncture maximum force -30 ¡ãC N ISO 6603-2 800¡¡
C Puncture energy 23 ¡ãC J ISO 6603-2 2.5 4.2
C Puncture energy -30 ¡ãC J ISO 6603-2 1.9¡¡
Ball indentation hardness¡¡N/mm² ISO 2039-1 230 130

Thermal properties
C Melting temperature 10 ¡ãC/min ¡ãC ISO 11357-1,-3 262¡¡
C Temperature of deflection under load 1.80 MPa ¡ãC ISO 75-1,-2 240¡¡
C Temperature of deflection under load 0.45 MPa ¡ãC ISO 75-1,-2 >250¡¡
C Temperature of deflection under load 8.00 MPa ¡ãC ISO 75-1,-2 185¡¡
Vicat softening temperature 50 N; 120 ¡ãC/h ¡ãC ISO 306 > 230¡¡
C Coefficient of linear thermal expansion, parallel 23 to 55 ¡ãC 10-4/K ISO 11359-1,-2 0.3¡¡
C Coefficient of linear thermal expansion, transverse 23 to 55 ¡ãC 10-4/K ISO 11359-1,-2 0.9¡¡
C Burning behavior UL 94 (1.6 mm) 1.6 mm Class UL 94 HB¡¡
Burning behavior UL 94 3.2 mm Class UL 94 HB¡¡
Glow wire test (GWFI) 0.8 mm ¡ãC IEC 60695-2-12 700¡¡
Glow wire test (GWFI) 1.6 mm ¡ãC IEC 60695-2-12 700¡¡
Glow wire test (GWFI) 3.0 mm ¡ãC IEC 60695-2-12 700¡¡
Burning behavior US-FMVSS302¡¡ ISO 3795 passed¡¡
C Vicat softening temperature 50 N; 50 ¡ãC/h ¡ãC ISO 306 > 230¡¡

Electrical properties (23 ¡ãC/50 % r. h.)
C Relative permittivity 100 Hz - IEC 60250 4.5¡¡
C Relative permittivity 1 MHz - IEC 60250 4.0¡¡
C Dissipation factor 100 Hz 10-4 IEC 60250 100¡¡
C Dissipation factor 1 MHz 10-4 IEC 60250 180¡¡
C Volume resistivity¡¡Ohm¡¤m IEC 60093 1E13¡¡
C Surface resistivity¡¡Ohm IEC 60093 1E14¡¡
C Electric strength 1 mm kV/mm IEC 60243-1 40¡¡
C Comparative tracking index CTI Solution A V IEC 60112 525¡¡

Other properties (23 ¡ãC)
C Water absorption (Saturation value) Water at 23 ¡ãC % ISO 62 5.5¡¡
C Water absorption (Equilibrium value) 23 ¡ãC; 50 % RH % ISO 62 1.9¡¡
C Density¡¡kg/m³ ISO 1183 1360¡¡
Bulk density¡¡kg/m³ ISO 60 700¡¡

Processing conditions for test specimens
C Injection molding-Melt temperature¡¡¡ãC ISO 294 290¡¡
C Injection molding-Mold temperature¡¡¡ãC ISO 294 80¡¡

Processing recommendations
Drying temperature dry air dryer¡¡¡ãC - 80¡¡
Drying time dry air dryer¡¡h - 2-6¡¡
Residual moisture content¡¡% Acc. to Karl Fischer¡¡0.03-0.12¡¡
Melt temperature (Tmin - Tmax)¡¡¡ãC - 280-300¡¡
Mold temperature¡¡¡ãC - 80-120¡¡

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.